toby is drafting the physical network topology plans for the new headquarters building for his company. which of the following will there be the most of within the building?

Answer:

do the wam wam

Explanation:

The heat flux is =1038kW/m² , the heat lost per hour is =259.5 kW, the heat lost per hour using a sheet of soda- lime glass.

The thickness of steel( t) = 10mm = 10× 10^-³m

The temperature difference on both sides = 300-100

∆T = 200°C

But the formula for heat flux = q = k∆T/t

Where K = thermal conductivity for steel = 51.9W/mK.

Substitute the variables into the formula for heat flux;

q = 51.9 × 200/10 × 10-³

q = 10380 × 10³/10

q = 10380000/10

q = 1038000 W/m² = 1038kW/m²

To calculate the heat lost per hour if the cross sectional area is = 0.25 m2 use the formula q × A

= 1038kW/m² × 0.25 m2

= 259.5 kW.

Learn more about heat flux here:

https://brainly.com/question/15217121

Answer:

winter viscosity grades

Explanation:

The “W”/winter viscosity grades describe the oil's viscosity under cold temperature engine starting conditions. There's a Low Temperature Cranking Viscosity which sets a viscosity requirement at various low temperatures to ensure that the oil isn't too thick so that the starter motor can't crank the engine over.

Answer:a

Ieieksdjd snsnsnsnsksks

During a static governor adjustment, the flyweights attached to the governor gear are in an inward position, closer to the governor cup shaft.

The flyweights move outwards from the governor gear, they increase the tension on the governor spring, which in turn affects the engine speed. By adjusting the governor spring tension with the flyweights in this position, the correct engine speed can be set.

When performing a static governor adjustment, the engine is usually at a standstill or operating at a low, idle speed. At this stage, the centrifugal force acting on the flyweights is minimal, causing them to move inward towards the governor cup shaft.

To know more about Flyweights attached visit:-

https://brainly.com/question/31631034

#SPJ11

Answer:

The correct answer is that a hydraulic power system is used for large amounts of force.

Explanation:

A pneumatic power system would be much more effective at focusing on a specific area. One person would be able to hold a pneumatic system, as the design can be made small. It can even be designed with a simple on/off switch.

The hydraulic system would fail because hydraulic power system is used for large amounts of force.

Energy or signals are transported through the static or dynamic forces of liquids in hydraulic power transmission systems. These fluid power systems are a subset of them. The two types of fluid power are hydraulics and pneumatics. The valves aid in controlling the liquid's flow and relieving pressure when necessary.

Pumps are used in hydraulic systems to force hydraulic fluid through the system and generate fluid power. The fluid flows to the cylinder, where the hydraulic energy is converted back into mechanical energy, after passing through the valves.

Therefore, Due to the hydraulic system's need for high levels of force, it would malfunction.

Learn more about the hydraulic system, refer to:

https://brainly.com/question/27961071

#SPJ5

Answer:

B....................

Answer:

The limit comparison test is a method used in calculus and real analysis to determine whether an infinite series converges or diverges.

The limit comparison test is based on the idea that if two series have the same behavior, meaning they both converge or both diverge, then their terms must be proportional to each other. Specifically, the limit comparison test states that if a given infinite series a_n has positive terms and the limit of the ratio of a_n and some other series b_n exists and is a finite positive number, then the two series have the same behavior.In other words, if the limit of a_n/b_n is a positive number L, then the series a_n converges if and only if the series b_n converges. If the limit of a_n/b_n is zero or infinity, then the series a_n and b_n have different behavior.

The limit comparison test is a useful tool for determining the convergence or divergence of a series that is difficult to evaluate directly. By comparing it with a known series that has a similar behavior, we can gain insight into whether the series converges or diverges.

When air is cooled below its dew point without condensation, it is said to be at a state of supersaturation. At this state, the air can hold more moisture than it typically would at its temperature and pressure

The dew point is the temperature at which air becomes saturated with moisture, leading to the formation of dew or condensation. When air is cooled below its dew point, it can no longer hold all of the moisture it contains, and the excess moisture condenses to form dew or other forms of precipitation. However, if the air is cooled below its dew point without condensation occurring, it is said to be at a state of supersaturation.

At this state, the air can hold more moisture than it typically would at its temperature and pressure. Supersaturation can occur when air is cooled rapidly, preventing moisture from condensing out of the air before it reaches a state of supersaturation. This can occur in a variety of situations, such as when air is rapidly cooled in a cloud or when humid air is rapidly transported to a colder region.

While supersaturation can occur without condensation, it is an unstable state. Any small disturbance can cause the excess moisture to condense out of the air, releasing latent heat in the process. This can lead to the formation of clouds or other forms of precipitation, such as rain or snow.

Learn more about condensation here: brainly.com/question/32145117

#SPJ11

The required flow rate of water can be calculated using the following formula:
Power = (Flow Rate) x (Acceleration due to Gravity) x (Height)
Here, Power = 0.80 MW, Acceleration due to Gravity = 9.81 m/s^2 and Height = 55 m.
So, Flow Rate = Power / (Acceleration due to Gravity x Height)
Substituting the given values, we get:

Flow Rate = 0.80 MW / (9.81 m/s^2 x 55 m) = 1.43 m^3/s
To convert this to m^3/min, we multiply by 60:
Flow Rate = 1.43 m^3/s x 60 = 85.8 m^3/min
If friction were included, a higher flow rate would be required because some of the energy of the water would be lost due to friction with the pipe walls, resulting in a lower overall efficiency of the system.
To calculate the required flow rate of water in m³/min, we'll use the following equation:
Power = (ρ * g * h * Q) / (60 * 1000)
Where:
Power = 0.80 MW (800 kW)
ρ = Density of water (1000 kg/m³)
g = Acceleration due to gravity (9.81 m/s²)
h = Height difference between the reservoir surface and the discharge point (55 m)
Q = Flow rate in m³/min
We need to solve for Q:
800,000 W = (1000 kg/m³ * 9.81 m/s² * 55 m * Q) / (60 * 1000)
800 = 9.81 * 55 * Q / 60
Now, we can solve for Q:
Q = (800 * 60) / (9.81 * 55)
Q ≈ 14.75 m³/min
So, the required flow rate of water is approximately 14.75 m³/min.If friction were included, a higher flow rate would be required. This is because some of the energy would be lost due to friction, resulting in a lower efficiency of the turbine. Consequently, to maintain the same power output, the flow rate must be increased to compensate for the energy loss.

To learn more about Acceleration click on the link below:

brainly.com/question/12550364

#SPJ11

In computer science, the recurrence relation is used to calculate the time complexity of a recursive function. Here, we are to write a recurrence relation for the running time of the recursive version of Insertion sort.

Insertion sort can be expressed as a recursive procedure as follows:In order to sort A[1…n], we recursively sort A[1…n−1] and then insert A[n] into the sorted array A[n−1].Algorithm to insert A[n] into the sorted array A[1..n-1]:1. Recursive call to sort A[1..n-1].2. Put the last element in the correct position by shifting the array. Let's denote the time taken by the function as T(n).The worst-case scenario happens when the input array is sorted in decreasing order. In this case, each time we enter the loop and slide an element to the right, we must compare it to each element in the sorted sub-array. Therefore, the time complexity of the insertion sort algorithm in the worst-case is O(n2). The recurrence relation for the running time of the recursive version of insertion sort is given by:T(n) = T(n-1) + nwhere n is the input size, T(n-1) represents the time taken by the function to sort n-1 elements, and n is the time taken to sort n elements.The base case for this recurrence is when there is only one element, i.e., T(1) = 1.The time complexity of insertion sort can be determined using the recurrence relation. So, T(n) is given by:T(n) = T(n-1) + n= T(n-2) + (n-1) + n= T(n-3) + (n-2) + (n-1) + n= ........= T(1) + 2 + 3 + ... + (n-1) + n= n(n+1)/2= O(n2)In conclusion, we can say that the time complexity of the recursive version of insertion sort is O(n2).

To know more about complexity, visit:

https://brainly.com/question/31836111

#SPJ11

Answer:

HVAC and wiring installation

Completed common areas

Explanation:

Core and shell development includes the installation of HVAC and wiring, as well as the completion of common areas. It does not typically include the installation of audio/video equipment or tenant-specific facilities, which are typically part of the tenant improvement process.

Answer:

A

Explanation:

Answer:

the answer is a

Explanation:

it is a because thats what the answer is

To determine the net power produced by the gas turbine power station, we need to calculate the work done by the turbine and the work done by the compressor. The net power produced is the difference between these two values.

The simple Brighton cycle consists of four processes:

Isentropic compression in the compressor.

Constant pressure heat addition in the combustion chamber.

Isentropic expansion in the turbine.

Constant pressure heat rejection to the surrounding environment.

Given data:

Inlet conditions:

Pressure at turbine inlet (P1) = 1 MPa

Temperature at turbine inlet (T1) = 1000 K

Exit conditions:

Pressure at turbine exit (P2) = 125 kPa

Temperature at turbine exit (T2) = 600 K

Heat expelled to the surrounding environment (Q_out) = 7922 kJ/s

Mass flow rate of air (m_dot) = 2.5 kg/s

First, let's calculate the specific enthalpy at state 1 (h1) using the air properties at the given temperature and pressure. You can refer to the air tables for this purpose.

Next, we need to calculate the specific enthalpy at state 2 (h2). We can use the temperature and pressure at state 2 and the air properties tables to determine h2.

Now, we can calculate the work done by the turbine (W_turbine) using the equation:

W_turbine = m_dot * (h1 - h2)

Since the compressor is assumed to be an isentropic process, the work done by the compressor (W_compressor) can be determined using the isentropic efficiency of the compressor (η_compressor) and the enthalpy difference between states 1 and 2:

W_compressor = (h2s - h1) / η_compressor

Where h2s is the specific enthalpy at state 2s, which can be determined using the temperature and pressure at state 2 and the air properties tables.

Finally, the net power produced (P_net) is given by:

P_net = W_turbine - W_compressor

Calculate the values using the above steps, and you will find the net power produced by the gas turbine power station.

To calculate the force required to lift a weight, we need to determine the mechanical advantage provided by the jackscrew. The mechanical advantage can be calculated as the ratio of the handle length to the pitch of the screw.

How to calculate the force required to lift a weight?

In this case, the mechanical advantage is:

255 mm / 5.00 mm = 51

This means that for every 51 turns of the handle, the screw will raise the load by a distance equal to the pitch of the screw, or 5.00 mm.

Now that we have the mechanical advantage, we can calculate the required force as follows:

Force = Weight / Mechanical Advantage

Force = 19,400 N / 51

Force = 380 N

So, a force of 380 N must be applied to the handle of the jackscrew to lift the 19,400 N weight.

To learn more about force, visit: https://brainly.com/question/25748369

#SPJ4

To complete the assignment, modularize your code using functions and classes. Utilize exception handling and implement two classes: "Store" with a constructor, setter method, and display method. Test your program thoroughly to avoid crashes and deductions in points.

To complete this assignment, you will need to use functions and classes to modularize your work. Additionally, you should utilize exception handling where necessary to ensure that your program does not crash on expected input. Failure to do so will result in a deduction of 50 points.

The main goal of this assignment is to create an application where the user can input the name and location of a store and then start their grocery shopping by adding items to a cart. To accomplish this, you will need to implement two classes with methods and attributes.

The first class you will need to implement is the "Store" class. This class should have a constructor that initializes two instance attributes: "name" and "location". Additionally, you should include a setter method that allows you to set the name and location of the store.

Lastly, you will need to implement a "display" method in the Store class. This method should output all the information from the Store class, including the name and location of the store.

Here is a step-by-step breakdown of what you need to do:

1. Define the Store class with the following attributes:
  - name
  - location

2. Implement a constructor in the Store class that takes the name and location as parameters and assigns them to the corresponding attributes.

3. Implement a setter method in the Store class that allows you to set the name and location of the store.

4. Implement a display method in the Store class that outputs all the information from the Store class, including the name and location of the store.

Remember, you have the flexibility to add extra methods or attributes as needed to complete the program successfully. Make sure to test your program thoroughly to ensure it functions as expected and does not crash on expected input.

Learn more about code : brainly.com/question/28338824

#SPJ11

To find the current through the 5-H inductor, we can use the relationship between voltage and current in an inductor, which is given by:

v(t) = L(di/dt)

Where v(t) is the voltage across the inductor, L is the inductance in henries, and di/dt is the rate of change of current with respect to time. Rearranging this equation, we get:

di/dt = v(t)/L

We can integrate both sides of this equation with respect to time to obtain the current through the inductor as a function of time:

i(t) = (1/L) * ∫[0 to t] v(τ) dτ

Substituting the given voltage function, we get:

i(t) = (1/5) * ∫[0 to t] (0.3012τ) dτ

= (0.06024/5) * t^2

= 0.012048 * t^2

Therefore, the current through the inductor at time t is given by 0.012048*t^2 amperes.

To find the energy stored within the inductor, we can use the formula for the energy stored in an inductor, which is given by:

W = (1/2) * L * i^2

Substituting the expression for i(t) that we obtained earlier, we get:

W = (1/2) * 5 * (0.012048*t^2)^2

= 0.000361152 * t^4 joules

To find the energy stored within the inductor for the time interval 0 < t < 5s, we can substitute t = 5s in the above expression and subtract the energy stored at t = 0s:

W(0 to 5) = 0.000361152 * (5^4 - 0)

= 45.144 * 10^-3 joules

Therefore, the energy stored within the inductor for the time interval 0 < t < 5s is 45.144 millijoules.

For such more question on voltage

https://brainly.com/question/1176850

#SPJ11

Given that the rod is initially in an unstressed state, finding the compressive force that is created in ABC as the temperature rises by 55°C yields a value of 156.902 kN.

Portion AB's size is 7.0695 X 10⁴ m².

BC portion's size is 1.96373 X 10³ meters.

505.725 X 106m for free thermal expansion is equal to (0.25)(11.7 X 106)(55) + (0.3)(20.9 X 106)(55).

Induced compressive force-induced shortening P= = 1.7682 X 10⁹ P + 1.455 10⁹ P = 3.2232 X 10⁹ P

3.2232 X 10⁹P = 505.725 X 10⁶ P = 156.902 X 103 N = 156.902 kN with zero net deflection.

As a result, ABC is subjected to a compressive force of 156.902 kN.

An action that seeks to preserve, modify, or deform a body's motion is called applying force.

Learn more about Compressive force here-

https://brainly.com/question/14663126

#SPJ4

Answer: b fixed and sliding

Explanation:

Answer:

at least 8 feet

Explanation:

Answer:

In this era, Sun Ra was among the first of any musicians to make extensive and pioneering use of synthesizers and other various electronic keyboards; he was given a prototype Minimoog by its inventor, Robert Moog.

Explanation:

Answer:

\(n=5.36kg\)

Explanation:

From the question we are told that:

Volume \(V=2.5m^3\)

Pressure\(\rho=500Kpa\)

Temperature \(T=28^o\)

Atmospheric pressure \(\rho_{atm} =97 kPa.\)

Generally the equation for an Ideal gas is mathematically given by

 \(PV=nRT\)

Therefore

 \(n=\frac{500*2.5}{8.314*28}\)

 \(n=5.36kg\)

With an energy input of 300 J and an efficiency of 15%, the machine produces 45 J of useable energy.

Energy is characterized as a quantitative characteristic that is transmitted to a person or a physical system and can be observed in the manner in which labor is accomplished as well as in the generation of heat and light. The sun is one of the most significant energy sources.

The machine's useful energy output, or work output, can be calculated as follows:

Efficiency = work out / work in x 100

0.15 = work out / 300

Multiply by cross

Production = 0.15 x 300

Production: 45 J

Thus, with an energy input of 300 J and an efficiency of 15%, the machine produces 45 J of useable energy.

To learn more about energy, refer to the link below:

https://brainly.com/question/1932868

#SPJ1

A risk register is a log of all potential hazards, risks, and uncertainties that a project may encounter. It also has an explanation of the probability of the danger occurring and its potential impact.

A risk register's purpose is to assist in the identification, assessment, and management of risks associated with a project and is an essential part of a successful risk management strategy. As such, the risk register has six components, including the risk description, risk cause, impact, risk likelihood, risk impact, and risk ranking.The following are six potential hazards for Project A and their explanations:

1. Weather Issues: Bad weather can slow down the construction process, make it dangerous to work outside, or damage materials.

2. Availability of Materials: If materials are scarce, it can delay or halt the construction project.

3. Time Constraints: Limited time can result in project delays or cutting corners, which can impact the quality of work.

4. Cost Overruns: Unexpected or uncontrollable costs can result in the project being halted or completed poorly.

5. Inadequate or Faulty Tools: This can affect work quality, safety, and efficiency, ultimately impacting the project schedule and costs.

6. Safety Issues: Inadequate safety protocols can result in accidents that could lead to injury or death of workers on the site.In conclusion, the risk register for Project A should outline potential hazards, their causes, impact, likelihood, and ranking, as well as mitigation strategies. The risk register should be reviewed and updated regularly to ensure that new risks are identified and addressed.

To know more about risk register visit:

https://brainly.com/question/31663618

#SPJ11

Answer:

The energy in pneumatic power systems is easily transmitted to gases, which absorb the energy of the system and lower its efficiency.

Explanation:

I did it on edge and got it right.

Answer:

The energy in pneumatic power systems is easily transmitted to gases, which absorb the energy of the system and lower its efficiency

Thanks for points!!! :D

Answer:

d. 1.0

Explanation:

Correlation identifies the relationship between two variables. In the given scenario there is strong relation between non ideal mixing. The correction factor can be between -1 to 1 depending on the intensity of the relationship and dependency. The non ideal mixing efficiency is highly dependent on the factors that govern it this means there is high intensity relation so the k is estimated to be nearly 1.

Answer:

i) Heat rejection =  1.0288 KJ

  Network production = 1.212 kJ

ii) Thermal efficiency = 54.08%

   mean effective pressure = 353.5 kPa

Explanation:

Given data :

Compression ratio ( r )  = 7

P1 ( initial pressure ) = 90 kPa,

T1 ( initial temperature ) = 27°C + 273 = 300 K

V1 = 0.004 m^3

Max cycle Temperature = 1127°C for each repetition of the cycle

i) Determine the heat rejection and net work production

considering that process 1-2 is an Isentropic compression

Find ; T2 = T1 ( r )^1.4-1

      T2 = 300 ( 7 )^0.4  = 653.371 K

    P2 = P1( r )^k

          = 90 ( 7 )^1.4  = 1372.081 kPa

considering that process 3-4 is an Isentropic expansion

T4 = T3 / r^k-1

    = 1400 / 7^(1.4 -1 ) = 642.82 K

Next ; Calculate the value of m

m = P1V1 / RT1   = 90(0.004) / 0.287 ( 300 )

                      m = 4.18 * 10^-3 kg

Finally :

amount of heat rejected = mCv ( T4 - T1 )

                                          = 4.18 * 10^-3 ( 0.718 ) ( 642.82 - 300 )

                                    Qout  = 1.0288 KJ

amount of heat added ( Qin ) =  mCv ( T3 - T2 )

                                                = 4.18 * 10^-3 ( 0.718 ) ( 1400 - 653.371 )

                   hence           Qin  = 2.2408 kJ

Network production( Wnet) = Qin - Qout

                                  = 2.2408 - 1.0288 ) KJ

                                  = 1.212 kJ

ii) Determine the thermal efficiency and mean effective pressure of the cycle

Thermal efficiency = 1 - Qout / Qin

                               = 1 - ( 1.0288 / 2.2408 )  = 54.08%

mean effective pressure = Wnet / V1 ( 1 - 1/r )

                                         = 1.212 / 0.004 ( 1 - 1/7 )

                                         = 353.5 kPa

Answer: hello the diagram related to your question is missing please the third image is the missing part of the question

Fx = 977.76 Ib/ft

Explanation:

Estimate the force that water exerts on the pier

V = 12 ft/s

D( diameter ) = 6 ft

first express the force  on the first half of the cylinder  as

Fx1 =  - \(-2\int\limits^\pi _\frac{\pi }{2} {Ps*cos\beta *a} \, d\beta\)   ---------------- ( 1 )

where ; Fy = 0

Ps = Po + 1/2 Pv^2 ( 1 - 4 sin^2β )  ------------- ( 2 )

Input equation (2)  into equation ( 1 )         (note :  assuming Po = 0 )

attached below is the remaining part of the solution

They are hosts on the same network, it is true. Subnet 255:248:0:0, IP 1.7.255.254, IP 1.2.3.4

You will most frequently encounter the subnet 255.255.255.0. As a result, if two addresses match in the first three sections (reading from left to right), and both addresses have the subnet 255.255.255.0, they are in the same subnet.

The network address is represented by the first 24 bits (the subnet mask's number of ones). The host address is represented by the final 8 bits, or the number of zeros in the subnet mask. You are given the addresses listed below: Address for the network: 11000000.10101000.01111011.00000000 (192.168.123.0)

To know more about hosts visit :-

https://brainly.com/question/28742495

#SPJ4

Answer:

Number1 = input("Choose a number: )

Number2 = input("Choose a second number: )

if number1 > number2:

print(number2\nnumber1)

else:

print(number1\nnumber2)

Explanation:

I'm assuming that you want it in python.