Need help tryna get a good grade

According to Technician A, fuel pump modules are spring-loaded so they can be compressed to fit the aperture.

Electric fuel pumps are often mounted in the fuel tank to utilize the fuel in the tank to cool the pump and ensure a steady supply of fuel. Each injector has a spring-loaded valve that is kept closed by the force of the spring. The valve doesn't open until fuel is squirted into it. The fuel pump driver module controls the voltage supplied to the fuel pump in a vehicle. By adjusting voltage, the module ensures ideal fuel pressure and flow to the engine throughout its entire operating range.

Learn more about voltage here-

https://brainly.com/question/29445057

#SPJ4

Answer: Neutrals

Explanation: System grounding on a power system is a term used to describe the entire processes involved when a neutral is used as the conductor to connect to the solid earth. This ensures that power is generated. This is usually done using either an inductor, an impendance or a resistor. It is very important and necessary to carry out a proper grounding of a power system in order to ensure the safety of the equipment and the personnel etc

The power of the braking system is fundamentally measured in brake torque. The effective radius, or how far away from the hub center the brake caliper acts on the disc, is that distance.

To learn more about Brake torque refer to:

https://brainly.in/question/19574584

#SPJ1

Brake torque is the primary measurement of the braking system's power. This distance is the effective radius, or the distance the brake caliper acts on the disc from the hub center.

To get the most out of an internal combustion engine's power and efficiency, the best ignition timing is needed to generate the most brake torque.

The ideal spark timing is always available for any engine operation. MBT works best with the throttle open, but idle engine operation is not ideal.

The term "brake torque" can be used to summarize the braking system's power. The effective radius is the distance from the hub center at which the brake caliper applies pressure to the disc.

The caliper's force divided by the system's effective radius is the braking torque. Brake torque is the force applied to the rotors to slow them down.

Learn more about brake torque:

brainly.com/question/24408653

#SPJ1

Answer:

the output of the IF amplifier consist of 675 kHz

Explanation:

Given the data in the question;

AM signal carrier frequency \(_{RF\)  = 460 kHz

Local oscillator frequency\(_{lo\) = 1135 kHz

Now, The output of the IF amplifier consists of difference of local oscillator frequency & AM carrier signal frequency;

FREQUECY\(_{IF\) = FREQUECY\(_{lo\) - FREQUECY\(_{RF\)

so we substitute in our given values

FREQUECY\(_{IF\) = 1135 kHz - 460 kHz

FREQUECY\(_{IF\) = 675 kHz

Therefore, the output of the IF amplifier consist of 675 kHz

Answer:

Isn't the answer written upside down in the sentence?

Explanation:

Answer:

The answer is D. Electrical switches had to become faster and much smaller.

Explanation:

I just took the test on ~ap.ex and got it right :)

Answer:

b

Explanation:

When designing a set of simple test programs to determine the type compatibility rules of a C compiler to which you have access, it is important to consider the different data types that are used in C programming. An example of a set of test programs that can be used to determine the type compatibility rules of a C compiler:

Integer Test the compatibility of the C compiler with integer data types. It declares two variables of type int, initializes them with values, and then adds them together. The result is printed to the screen. If the program compiles and runs without any errors, then the C compiler is compatible with integer data types.

Floating-Point Test  the compatibility of the C compiler with floating-point data types. It declares two variables of type float, initializes them with values, and then adds them together. The result is printed to the screen. If the program compiles and runs without any errors, then the C compiler is compatible with floating-point data types.

By running the set of simple test programs described above, you can determine the type compatibility rules of a C compiler to which you have access. If any of the programs do not compile or run without errors, then you can determine which data types are not compatible with the C compiler and adjust your code accordingly.

To know more about compiler visit:-

https://brainly.com/question/28232020

#SPJ11

Allen made a Venn diagram to compare radiation and conduction. The diagram shows two intersecting circles, with the left circle labeled radiation, the right circle labeled conduction.

The overlapping region between the two circles is labeled "Y."The label that belongs in the area marked Y is "Occurs when molecules are in direct contact."Conduction occurs when molecules are in direct contact with each other. When two objects or substances are in contact, energy flows from the hotter object to the cooler object until both objects are at the same temperature.Radiation, on the other hand, does not require matter to transfer energy.

It involves the transfer of energy in the form of waves or particles through a vacuum or a transparent medium. Radiation is the transfer of heat from one body to another in the form of waves or rays.Most of the time, radiation and conduction occur at the same time. A good example of this is the transfer of heat through a metal pot. In this case, the heat from the burner is transferred to the metal pot through conduction, and then it is transferred to the food inside the pot through radiation.

To know more about radiation visit:

https://brainly.com/question/31106159

#SPJ11

As a small business owner, it is crucial to assume the responsibility of determining whether the building space being leased is properly zoned for the intended usage of the business. Zoning regulations vary by location and are set in place to ensure the appropriate use of land and buildings within a community. By understanding and adhering to zoning requirements, business owners can avoid potential legal issues, penalties, and disruptions to their operations. Proper zoning also ensures compatibility with neighboring businesses and maintains the overall integrity of the community. Taking the time to research and confirm zoning regulations before leasing a space demonstrates responsible business ownership and contributes to the long-term success and sustainability of the business.

#SPJ11

9514 1404 393

Answer:

  1

Explanation:

Only one such circle can be drawn. The diameter of the 10" circle will be a radius of the semicircle. In order for the 10" circle to be wholly contained, the flat side of the semicircle must be tangent to the 10" circle. There is only one position in the figure where that can happen. (see attached).

Answer:

Based upon the Von Mises theory, the safety factor for points A and B are 2.77 and 6.22 respectively.

From the diagram of this bar made of AISI 1006 cold-drawn steel shown in the image attached below, we can logically deduce the following parameters:

At point A, the stress is given by this equation:

σx = Mc/I + P/Area

\(\sigma_x = \frac{Fl(\frac{d}{2}) }{\frac{\pi d^2}{64} } +\frac{P}{\frac{\pi d^2}{4} } \\\\\)

σx = 32Fl/πd³ + 4P/πd²

Substituting the given parameters into the formula, we have;

σx = 32(550)(0.1)/π(0.02)³ + 4(800)/π(0.02)²

σx = 95.49 MPa.

Next, we would determine the torque:

Mathematically, torque can be calculated by using this formula:

τxy = Tr/J = 16T/πd³

τxy = 16(30)/π(0.02)³

τxy = 19.10 MPa.

From Von Misses theory, we have:

σVM = √(σx² + 3τxy²)

σVM = √(95.49² + 3(19.10)²)

σVM = 101.1 MPa.

Now, we can calculate the safety factor for point A:

n = Sy/σVM

n = 280/101.1

n = 2.77.

At point B, the stress is given by this equation:

σx = 4P/πd²

σx = 4(800)/π(0.02)²

σx = 25.47 MPa.

Next, we would determine the torque:

Mathematically, torque can be calculated by using this formula:

τxy = Tr/J = 16T/πd³ + 4V/3A

τxy = 16(30)/π(0.02)³ + 4(550)/3π(0.02)³

τxy = 21.43 MPa.

From Von Mises theory, we have:

σVM = √(σx² + 3τxy²)

σVM = √(25.47² + 3(21.43)²)

σVM = 45.02 MPa.

Now, we can calculate the safety factor for point B:

n = Sy/σVM

n = 280/45.02

n = 6.22.

Read more on Von Mises theory here: https://brainly.com/question/12976779

#SPJ1

Answer:

Compressed air systems usually consist of the following components:

compressor.

air cooler.

air receiver tank.

filter.

dryer.

condensate trap.

distribution system

Answer:

Compressed air systems usually consist of the following components:

compressor.

air cooler.

air receiver tank.

filter.

dryer.

condensate trap.

distribution system

Explanation:

Compressed air systems usually consist of the following components:

compressor.

air cooler.

air receiver tank.

filter.

dryer.

condensate trap.

distribution system

Therefore, the value assigned to secondDouble when the code segment is executed is 2.5 (option E).

When the code segment is executed, the value assigned to secondDouble can be determined by following the order of operations (operator precedence) and type conversions in the expression:

firstInt is not explicitly assigned a value, so its initial value is undefined.

The expression firstInt secondInt performs integer multiplication of firstInt and secondInt, resulting in the value 0 (since firstInt is initialized to 0).

The expression firstInt secondInt / firstDouble performs integer division of the result from the previous step (0) by firstDouble (2.5), resulting in 0.

The expression 0 + 2.5 performs addition of 0 and 2.5, resulting in 2.5.

Finally, the value 2.5 is assigned to secondDouble.

To know more about code segment,

https://brainly.com/question/30592934

#SPJ11

A variable is a value in programming that is subject to change based on external factors or data that has been passed into the program.

To learn more about computer program refer to:

https://brainly.com/question/23275071

#SPJ4

Call Interface for Oracle Custom apps can be made thanks to OCI's native C/C++ interfaces for interfacing with the Oracle Database. Again, more powerful physical machines with higher

A databases is a group of data that has been organized to make it simple to update and manage. Data records or files including data such as a invoice number, client information, bank records, and product information are commonly collected and stored in computer databases.

A collection is a purposeful gathering of data. They enable the digital manipulation and archiving of data. Databases make managing data easier. Take a look at a store as an.

To know more about database visit;

https://brainly.com/question/16991295

#SPJ4

Technician we says that on many imported cars the turn signal lens is red. Technician B says that on many imported cars, the brake light lens is yellow. So, the answer is technician A is wrong, and Technician B is also wrong.

In most cases, the front turn signal lenses of a vehicle are amber in colour, while the rear turn signal lenses are red. In the United States, the use of red lenses on the rear of a car, truck, or motorcycle indicates the presence of brake lights. Similarly, yellow or amber lenses are used on the rear of the vehicle to indicate turn signals. The colour of the lens of the turn signal of a vehicle is amber, and the colour of the lens of a brake light is red. When you are driving a car, you should have a clear understanding of the purpose of each of your vehicle's lights. Many imported vehicles may follow a different colour code, but the domestic vehicles usually follow the red colour for brake lights and amber for turn signals.

to know more about signal lens visit;

https://brainly.com/question/27752994

#SPJ11

Answer:

ee

Explanation:

This is an over the top question

The program requires a sequence control structure; First, we get input for the variables, and then use the formula to calculate the amount of calories burnt.

The program in python is as follows, where comments (in italics) are used to explain each line.

#This gets input for age, in years

age = int(input("Age (years): "))

#This gets input for weight, in pounds

weight = int(input("Weight (pounds): "))

#This gets input for heart rate, in beats per minutes

heart_rate = int(input("Heart Rate (beats per minutes): "))

#This gets input for time, in minutes

time = int(input("Time (Minutes) : "))

#This calculates the calories burnt for men

calories_man = ((age * 0.2017) - (weight * 0.09036) + (heart_rate * 0.6309) - 55.0969) * time / 4.184

#This calculates the calories burnt for women

calories_woman = ((age * 0.074) - (weight * 0.05741) + (heart_rate * 0.4472) - 20.4022 ) * time / 4.184

#This prints the calories burnt for men

print('Men: %0.2f calories' % calories_man)

#This prints the calories burnt for women

print('Women: %0.2f calories' % calories_woman)

Please note that the program does not check for valid inputs

See attachment for program output

Read more about Python programs at:

https://brainly.com/question/22841107

Answer:

"cool"

Explanation:

No, the physical address 346E0 cannot be the starting address for a segment. This is because the starting address of a segment must be aligned with the segment's size or boundary, which is determined by the processor's architecture.

Segment boundaries are defined by 16-byte or 4-byte boundaries, depending on the segment's use. Therefore, the starting address of a segment must be a multiple of 16 or 4, respectively, depending on the segment type.

In the given address 346E0, the last digit is 0, which indicates that it is a multiple of 16. However, we do not have enough information about the processor architecture and segment size to determine whether this is an appropriate starting address for a segment.

In general, when defining a segment, it is important to ensure that the starting address is properly aligned with the segment's boundary to avoid any issues with memory access and processing.

Learn more about segment boundaries here : brainly.com/question/30000398

#SPJ1

Sandpaper.

Rubble.

Pyramid.

Wrinkled.

Marbled.

Answer:

using standardized parts

Explanation:

In summary, the XYZ Company will require:

(a) 705 processing and assembly operations,

(b) 710 workers (direct labor only), and

(c) 25,738 m2 of total floor space for the new plant.

To calculate the required processing and assembly operations, workers, and total floor space for the new factory, we can break down the problem into smaller parts and analyze each element.

(a) Processing and assembly operations:

Number of components made in the factory: 250 components * 35% = 87.5 (round up to 88 components)

Processing operations for components: 88 components * 8 processing operations = 704 processing operations

Assembly operations for final product: 1 assembly operation (as each product is assembled in one workstation)

Total operations = 704 processing operations + 1 assembly operation = 705 operations

(b) Number of workers (direct labor only):

Processing workers: 704 processing operations / 1 (one worker per work cell) = 704 workers

Assembly workers: 13 models * 1000 units/model = 13,000 units/year

Assembly time per unit: 48 min/unit = 0.8 hr/unit

Assembly time for all products: 13,000 units * 0.8 hr/unit = 10,400 hr

Assembly workers required: 10,400 hr / 2,000 hr/shift = 5.2 (round up to 6 workers)

Total workers = 704 processing workers + 6 assembly workers = 710 workers

(c) Total floor space required:

Processing floor space: 704 work cells * 25 m2/cell = 17,600 m2

Assembly floor space: 6 workstations * 25 m2/station = 150 m2

Total production area: 17,600 m2 + 150 m2 = 17,750 m2

Additional allowance (45%): 17,750 m2 * 45% = 7,987.5 m2

Total floor space = 17,750 m2 + 7,987.5 m2 = 25,737.5 m2 (round to 25,738 m2)

In summary, the XYZ Company will require:

(a) 705 processing and assembly operations,

(b) 710 workers (direct labor only), and

(c) 25,738 m2 of total floor space for the new plant.

Read more about production area here:

https://brainly.com/question/13188253

#SPJ1

As the temperature of wire increases, the electrical resistance of wire increases. The correct option is B.

The resistance is the property of material which opposes the current through the wire to pass.

A complete circuit is left on for several minutes causing the connecting copper wire to become hot.

The resistance is directly proportional to the temperature. So, when temperature is increased, the resistance of a wire also increases. The current will have more opposition to flow.

Thus, the correct option is B.

Learn more about resistance.

https://brainly.com/question/11431009

#SPJ4

The reference source that can be consulted is C. The Professional Engineers Act and Board Rules

The reference source that may be consulted to answer questions regarding the Professional Engineers Act is the Professional Engineers Act and Board Rules.

The Professional Engineers Act and Board Rules is an Act that was established in order to regulate the qualifications for professional engineers, register them and also make sure that their conducts and behavior are looked into.

Learn more about engineers on:

https://brainly.com/question/4231170

A high-pass filter is a type of electronic circuit that allows high-frequency signals to pass through while attenuating or blocking low-frequency signals. In this case, the high-pass filter consists of a 1.54 μF capacitor and a 115 ω resistor in series. The circuit is driven by an AC source with a peak voltage of 5.00 V.

To determine the behavior of the high-pass filter, we can calculate its cutoff frequency, which is the frequency at which the filter starts to attenuate the input signal. The cutoff frequency (f) can be calculated using the formula:

f = 1 / (2πRC)

where R is the resistance (115 ω) and C is the capacitance (1.54 μF).

Plugging in the values, we have:

f = 1 / (2π * 115 * 1.54 * 10^-6)

Calculating this expression gives us the cutoff frequency of the high-pass filter. From there, we can analyze how the filter behaves at different frequencies.

To know more about frequency visit :

https://brainly.com/question/29739263

#SPJ11

To determine the blocks that must be read from and written to the disk for each operation in different disk block allocation schemes, we need to consider the characteristics of each scheme and analyze the given sequence of operations.

The disk block allocation schemes and their impact on the required read and write operations. In the contiguous allocation scheme, where files occupy consecutive blocks, the read operation for block D would require accessing block D directly. Similarly, the read operation for block F would require accessing block F directly. The delete operation of block E would entail modifying the file control information to skip block E. Finally, inserting a new block C' between C and D would involve shifting subsequent blocks and updating the file control information accordingly.

In the linked allocation scheme, where blocks are linked together via pointers, the read operation for block D would involve traversing the linked blocks until reaching block D. Similarly, the read operation for block F would involve traversing the linked blocks until reaching block F. The delete operation of block E would entail updating the pointers to bypass block E. Inserting a new block C' would require finding a free block and updating the pointers accordingly

Using the File Allocation Table (FAT) scheme, the read operation for block D would involve checking the FAT to find the location of block D. Similarly, the read operation for block F would involve checking the FAT to find the location of block F. The delete operation of block E would require updating the FAT to mark block E as free. Inserting a new block C' would involve finding a free block, updating the FAT to allocate it, and adjusting the pointers accordingly.

In the indexed allocation scheme, where each file has an index block containing pointers to its data blocks, the read operation for block D would involve accessing the index block to find the location of block D. Similarly, the read operation for block F would involve accessing the index block to find the location of block F. The delete operation of block E would require updating the index block to remove the pointer to block E. Inserting a new block C' would involve finding a free block, updating the index block to include a pointer to the new block, and adjusting the pointers accordingly.

Learn more about allocation

brainly.com/question/29976811

#SPJ11

The accuracy of a digital multimeter might be stated by the manufacturer as +0.5 % reading + 1 digit".

A digital multimeter has been known  an instrument that has been used to measure a plethora of electrical settings. The multimeter able to read voltage, current, resistance, among others.

This allows the user to be able to make sure that the wiring of an object is done properly and will not lead to electrocution or a short circuit.The MIN/MAX feature of a digital multimeter is being used to evaluate an oxygen sensor.

Therefore, The accuracy of a digital multimeter might be stated by the manufacturer as +0.5 % reading + 1 digit".

Learn more about  multimeter on:

https://brainly.com/question/30809641

#SPJ9